Unilumin Upanel II 0.9 MIP specs
MIP packaging with pixel-level bin mixing, superior consistency and uniformity EBL2.0 surface treatment with higher contrast ratio 7680Hz high refresh rate for smooth and fluid visuals Full flip-chip common cathode design, ultra-low power consumption
Physical
- Pixel pitch
- 0.953 mm
- Cabinet size (W×H×D)
- 610 × 343 × 68 mm
- Weight
- 7 kg
- Weight per m²
- 33.5 kg/m²
- Cabinet type
- Fixed install
- Service access
- Front
Image
- Cabinet resolution
- 640 × 360 px (16:9)
- Pixel density
- 1,101,068 px/m²
- Brightness (calibrated)
- 600 nits
- Refresh rate
- 7,680 Hz
- Contrast
- 10,000:1
- Viewing angle (H/V)
- 170° / 165°
- LED type
- MIP
Power & thermal
- Max power
- 68 W
- Average power
- 47 W
- Max power per m²
- 325 W/m²
- Average power per m²
- 225 W/m²
- Thermal load
- 232 BTU/h per cabinet
Environment
- Rated for
- Indoor
- IP rating (front)
- IP60
- IP rating (rear)
- IP60
- Operating temperature
- -10 to 45 °C
Manufacturer details
- Power supply
- 100~240VAC
- Storage temp
- -20℃~+55℃
- Site category
- Professional
- Pitch published
- 0.953mm
- Power published
- 68W/panel@600nits, 99W/panel@1200nits (Ave. 47W/57W)
- Cabinet material
- Die-cast Aluminum
- Weight published
- 7±0.3kg/panel
- Color temperature
- 2,000 - 9,500 K Adjustable
- Datasheet version
- MIP brochure 7.11
- Contrast published
- 10000:1~20000:1
- Operating humidity
- 10~80%RH
- Pixel configuration
- MIP
- Brightness published
- 600~1200 cd/m²
All variations in the Upanel II MIP series
All Unilumin cabinets →Every Unilumin Upanel II MIP series cabinet and the exact pitch, size and brightness pairing it ships with.
- Upanel II 0.9 MIPthis model0.953 mm610×343 mm600 nits
- Unilumin Upanel II 1.2 MIP1.27 mm610×343 mm600 nits
- Unilumin Upanel II 1.5 MIP1.588 mm610×343 mm600 nits
Controllers that drive this panel
All controllers →Each cabinet carries 230,400 px, so a controller's port budget and total capacity decide how much wall it drives. Its receiving card is not published — confirm the control ecosystem with your supplier before ordering.
- Colorlight U15 MaxColorlightConfirm ecosystem
800cabinets
400 × Mixed520M px total · port-bound
Wire it - NovaStar H20NovaStarConfirm ecosystem
800cabinets
400 × Mixed260M px total · port-bound
Wire it - NovaStar MX6000 ProNovaStarConfirm ecosystem
611cabinets
64 × Mixed141M px total · capacity-bound
Wire it - NovaStar H15NovaStarConfirm ecosystem
400cabinets
200 × Mixed130M px total · port-bound
Wire it - Colorlight U9 MaxColorlightConfirm ecosystem
200cabinets
100 × Mixed260M px total · port-bound
Wire it - Colorlight U6 MaxColorlightConfirm ecosystem
200cabinets
100 × Mixed130M px total · port-bound
Wire it
Counts assume one cabinet per port-chain hop at 60 Hz / 8-bit. Open Unilumin Upanel II 0.9 MIP in the calculator to lay out the real chains and validate them.
Design a wall with this panelFrequently asked
- How much power does the Unilumin Upanel II 0.9 MIP draw?
- Each Unilumin Upanel II 0.9 MIP cabinet draws up to 68 W at full white and about 47 W with typical content — 325 W/m² max. A 10-cabinet wall therefore needs up to 680 W plus headroom.
- What is the resolution of the Unilumin Upanel II 0.9 MIP?
- One cabinet is 640 × 360 pixels at a 0.953 mm pixel pitch (1,101,068 px/m²). About 6 cabinets side by side reach 4K width (≈ 3.66 m).
- How heavy is a Unilumin Upanel II 0.9 MIP wall?
- A single cabinet weighs 7 kg (33.5 kg/m²). A 5 × 3 wall of 15 cabinets weighs about 105 kg before mounting structure.
- Is the Unilumin Upanel II 0.9 MIP suitable for outdoor use?
- No — the Unilumin Upanel II 0.9 MIP is an indoor cabinet (IP60 front). Its 600 nits suit controlled lighting, not direct sun.
Size a wall with the Upanel II 0.9 MIP
Dimensions, resolution, power, weight and a validated wiring diagram — free, no account needed.