Skip to content
wikiLED
2.5 mm pitchIndoorSMD

INFiLED IRGL2.5 specs

Dual-sided indoor LED display engineered for airports, transit hubs and retail — where every direction deserves an equally compelling message.

Pitch
1.56 mm2.5 mm
Size
600×675 mm
Nits
1,500 nits600 nits
Open in calculatorCompareControllersRunning costDatasheet
INFiLED IRGL2.5 LED cabinet

Physical

Pixel pitch
2.5 mm
Cabinet size (W×H×D)
600 × 675 × 27 mm
Weight
8.7 kg
Weight per m²
21.5 kg/m²
Cabinet type
Fixed install
Service access
Front

Image

Cabinet resolution
240 × 270 px (8:9)
Pixel density
160,000 px/m²
Brightness (calibrated)
600 nits
Refresh rate
3,840 Hz
Contrast
5,000:1
Viewing angle (H/V)
160° / 160°
LED type
SMD
Processing depth
14 bit

Power & thermal

Max power
280 W
Average power
93 W
Max power per m²
691 W/m²
Average power per m²
230 W/m²
Thermal load
955 BTU/h per cabinet

Environment

Rated for
Indoor
IP rating (front)
IP30
IP rating (rear)
IP30
Operating temperature
-10 to 45 °C
LED lifetime
100,000 h
Certifications
CE, FCC, ETL, RoHS

Manufacturer details

Driver ic
PWM Driver Chip
Scan rate
1/60
Brochure url
https://www.infiled.com/wp-content/uploads/2026/07/geminiled-series_brochure-1.pdf
Control mode
Synchronous display
Power supply
100-240V AC 50-60Hz
Signal input
DVI, HDMI, DP, SDI
Transparency
0%
Site category
Fixed Installation
Display colors
4.4T
Frame rates hz
50/60Hz
Led wavelength
R: 620-625nm, G:510-535nm, B: 455-480nm
Receiving card
NovaStar
Pitch published
2.5mm
Power published
280 / 93.3 W/panel (max / avg)
Cabinet material
Die-casting Magnesium
Control distance
Ethernet cable≤100m or Fiber Optic≤15km
Physical density
160,000 pixels/m²
Weight published
8.7kg (19.18lb)
Color temperature
6500K(3200K~9300K adjustable)
Module dimensions
300x337.5mm
Module resolution
120x135pixels
Contrast published
5000:1
Lifetime published
≥100,000h
Operating humidity
10-90%RH Non-condensing
Grayscale published
14bit
Pixel configuration
3 IN 1 SMD
Brightness published
600nits
Brightness adjustment
0~100%, 256 levels
Service access published
Front

All variations in the GeminiLED series

All INFiLED cabinets →

Every INFiLED GeminiLED series cabinet and the exact pitch, size and brightness pairing it ships with.

Controllers that drive this panel

All controllers →

Each cabinet carries 64,800 px, so a controller's port budget and total capacity decide how much wall it drives. Its receiving card is not published — confirm the control ecosystem with your supplier before ordering.

Counts assume one cabinet per port-chain hop at 60 Hz / 8-bit. Open INFiLED IRGL2.5 in the calculator to lay out the real chains and validate them.

Design a wall with this panel

Frequently asked

How much power does the INFiLED IRGL2.5 draw?
Each INFiLED IRGL2.5 cabinet draws up to 280 W at full white and about 93 W with typical content — 691 W/m² max. A 10-cabinet wall therefore needs up to 2,800 W plus headroom.
What is the resolution of the INFiLED IRGL2.5?
One cabinet is 240 × 270 pixels at a 2.5 mm pixel pitch (160,000 px/m²). About 16 cabinets side by side reach 4K width (≈ 9.60 m).
How heavy is a INFiLED IRGL2.5 wall?
A single cabinet weighs 8.7 kg (21.5 kg/m²). A 5 × 3 wall of 15 cabinets weighs about 131 kg before mounting structure.
Is the INFiLED IRGL2.5 suitable for outdoor use?
No — the INFiLED IRGL2.5 is an indoor cabinet (IP30 front). Its 600 nits suit controlled lighting, not direct sun.

Size a wall with the IRGL2.5

Dimensions, resolution, power, weight and a validated wiring diagram — free, no account needed.

Open in calculatorCompare with competitors